Back to TOP
Search
3SX
3SX Search
3SX

ʘ¿ʘ SEARCH 3SX

Detailed Search

3SX



3SX
3SX



3SX
3SX Catalog
3SX
3SX AWD Dyno

3SX Powder Coating

-  * CLEARANCE *

-  3SX CARS - USED VEHICLES

-  3SX Designs

-  3SX Identity Gear

-  3SX Polishing

-  3SX Powder Coating

-  Alcohol/Water Injection

-  Blow Off Valves

-  Body & Lighting

-  Boost Controllers

-  Brakes

-  Clutches & Flywheels

-  Cooling

-  Datalogging & WIDEBAND

-  Detailing & Accessories

-  Drivetrain

-  Electronics

-  Engine External Bolt-On

-  Engine Internal Lower

-  Engine Management

-  Engine Motor Mounts

-  Engine Upper

-  Exhausts - Non-Turbo

-  Exhausts - Turbo

-  Fluids

-  Fuel

-  Fuel Kits - 3SX Custom

-  Gaskets & Seals

-  Gauges

-  Gift Certificates

-  Hardcore Racing!

-  Harness & Wiring

-  Ignition

-  Intakes

-  Intercoolers

-  Interior

-  JDM / GTO / RHD / 6G74

-  Literature & Manuals

-  Nitrous

-  PHENIX HOSE & FITTINGS

-  Regular Maintenance

-  Seats

-  Sensors & Senders

-  Shifters & Knobs

-  STARION / CONQUEST

-  Steering & Chassis

-  Stock Mitsubishi Parts

-  Suspension - Horizontal

-  Suspension - Vertical

-  Tools

-  Transfer Case

-  Transmission & Differential

-  Transmission - USED

-  Trinkets & Trash

-  Turbo Timers

-  Turbos

-  Wastegates

-  Wheels

-  1-Off NEW Parts

-  Used Parts

 
3SX LINE CARD
 
3SX Gatherings
3SX



3SX
3SX GTO POLICE
Paper Cutout

Model GTO Cutout

Click to download yours!
3SX



3SX Custom Fuel Pump Bulkhead Sending Unit Assembly
With FueLab Prodigy Fuel Pump

After 2 years in development we have finally released our 3SX Fuel Pump Sending Units! These units define versatility in your fuel system - from STOCK to 1000+ hp! These kits include custom aluminum bulkheads that are basically the LAST sending unit you'll ever buy! They are set up with AN10 ports for feed and AN8 ports for return - meaning they can be adapted down to serve as a stock replacement unit on a stock SOHC or adapted to run however much fuel and power you are going for! The wiring is properly insulated and "putty'd" in place ensuring a safe seal for the electrical connections - no "nuts-n-nylon-washers" here! The hanger bracket accommodates all of the "smaller" pumps from Walbro, Aeromotive, and AEM. Or remove the bracket and the giant Fuelab Prodigy pumps directly attach to the sending unit allowing for up to their 1800hp rated 722 lph / 190 gph 42402 series pump!

THIS particular listing is offers BIG FUEL options using the FueLab Prodigy pumps that are fully capable of operating in-tank... and depending on you pump selection, flow up to 722 lh with a 1800hp rating!!!

All of these sending unit bulkhead kits INCLUDE a new OEM gasket/seal for where the sending unit mounts to the tank. The fuel gauge level/bobber assembly is NOT included.

 

3SX Fuel Sending Unit with FueLab Prodigy Pump and Fittings

These fuel kits include the following parts:
3SX custom aluminum Fuel Hat / Bulkhead
Black FueLab Prodigy Fuel Pump - Select Flow
FueLab 75u Stainless Pickup Strainer
90-degree AN10 Feed/Output Fitting
90-degree AN8 Return/Input Fitting
AN10 Adapter to connect pump to bulkhead
AN8 adapter and return tube
OEM Fuel Sending Unit Gasket

KIT #
Pump # / HP Rating
Flow LPH
Flow GPH
BH20
40401 - 700 hp
285
75
BH21
41401 - 1000 hp
399
105
BH22
41402 - 1300 hp
532
140
BH23
42401 - 1500 hp
646
170
BH24
42402 - 1800 hp
722
190

 

Installation Notes
1) You will have to transfer your original gauge sender and bobber from your old sending unit to this one. It's only 2 screws.
2) You will also have to wire this unit into your factory system. Instructions are included.
3) Disconnecting the factory fuel sending line can be a challenge. This hose can often get corroded or damaged from trying to remove it to either drop the fuel tank or remove the fuel sending unit.  It is recommended that you disconnect this line FIRST from the long line running up under the vehicle rather than at sending unit - the line's ends are not swivels and can damage the sending unit if you try to disconnect it there first. You can see this line from under the car near between the tank and rear subframe assembly as pictured here.

4) You may need to modify the fuel sending unit cover plate a little to allow for clearance of the fittings. Alternately, you could just space it up as it is not a "sealed" cover.
5) A new OEM fuel pump sending unit gasket/seal IS included!

 

 

Wiring Harness Plug End
Now that we have sourced various harness plug connectors, we are also INCLUDING the male and female 3SX 6-pin 2x3 Harness Plug Connectors so you can more easily wire your new bulkhead to plug into the stock wiring!

 

 

If your fuel sending unit looks like this one below, then you NEED one of these kits!!!

 

 


Review This Product!


Add to wish list

Select desired item from drop-down Options Menu
Quantity  
 
 

3SX
3SX Cart
3SX
3SX



3SX
3SX Login
3SX
3SX



3SX
3SX Features
3SX
3SX
Check THIS Out!
3SX Click Click Start Relay
3SX
3SX
3SX
Check THIS Out!
Business Card Holders - Automotive Style!
3SX
3SX



3SX
3SX Ships via UPS - Find Your Order!
Where's My Order?
Enter your 6-digit web order number to track your order.
3SX



3SX
Become a 3SX FAN
on FaceBook!
3SX



3SX
3SX



3SX
Follow 3SX on Twitter
3SX on Twitter
3SX



3SX

Get our 3SX Newsletter!
Enter Your eMail
You will receive a confirmation email - please click the link to be added.
3SX



3SX
3SX Racing
3SX



3SX 3SX